Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
He is welcome in my house and has permission to work on my HVAC. Awesome technician and a really great guy! Send him to my house anytime!!
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
Jeremy did a great job and was willing to come out late and work until the job was done. Everyone I dealt with was extremely nice and sincere!
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
The technician you sent was a consummate professional!! He answered all my questions and verified my units were operating at max efficiency. He was polite and was a very knowledge on the systems. He talked through several options of things I wanted to add to my house unit as I was asking if steam was better for a humidifier. We also talked about getting our ducts cleaned since we have never done it while living in our house. Send him as my technician any time.
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
Thank you Jeremy for being awesome. We called Jeremy out to check a wet spot on our ceiling. He was able to confirm it was not the A/C unit and identified the source. Then switched gears and gave us a quote on converting our propane water heater into an electric one. I am always ecstatic about the service I receive from Loving Air.
Overall Experience
Quality
Price
Convenience
James is absolutely wonderful. I’d trust him with any work I need done - didn’t try to upswell me. Didn’t treat me as uneducated but was more than willing to teach me if I was interested. 15/10 would bring him back.
Overall Experience
Quality
Price
Convenience
Great service… professional and prompt. Outstanding!!!
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
Overall Experience
Quality
Price
Convenience
Ryan was so informative and thorough and fixed all my issues professionally. Saving his card and will be using his service always.
Overall Experience
Quality
Price
Convenience
arrived to customers residence and was greeted by customer and was led to thermostat. Thermostat is functioning properly at this time. Put refrigerant gages on system on outside unit and has suction pressure of five psi and liquid pressure of 50 at this time. inspect 45/5 Capacitor and is within range this time reading 44.8/5.2 At this time. Inspector condenser oil has little lights dust at this time. Inspected fan motor and blade and they are functioning properly at this time. Fan motor has a drawl of .7 A at this time. Inspected fan motor seals found no evidence of oil leaks from bearings at this time. Refrigerant lines are tight and neat and arm flex. Insulation is intact without any visible defects at this time. Inspected out outside disconnect Square D box with breaker. It is functioning properly at this time. > inspected single pole contactor and it has 246.3 V coming in and out at this time and is functioning properly at this time. Outdoor unit is sitting level on bracket tha
Arrived at customers residence and was greeted by the customer and was led to the thermostat and it,is functioning properly at this time. Inspected 20x20x1 and 2 14x14x1 filters and they are clean at this time. Tape and duct work joints are tight and neat and and without any visible defects or issues at this time. Refrigerant lines are tight and neat at this time and Arma flex insulation is tight and neat and without any visible defects at this time.Electrical connections are tight and neat to the components at this time and wire nut connections are tight and neat and without any visible defects at this time. Inspected condensate I drain and it is clear at this time and also inspected condensate pump and it is functioning properly at this time. Inspected 60 amp circuit breaker and it is functioning properly at this time. Inspected evaporator coil and it is clean at this time. Inspected blower motor and wheel and they are functioning properly at this time. Inspected blower motor and w
customer making decision in a week. Requested that I email them Trane quotes customer interested in trane only
Completed inspection on system. Electrical connections are tight. Blower wheel and evap coil are clean. Blower motor and heater packs amping within specs. Cleaned and flushed drain line. Ensuring water safeties functioning properly. Unit is level and draining properly. All ductwork is tight and secure. Reassembled system and proceeded outside. Completed inspection on outdoor unit. Electrical connections are tight. Compressor, cond fan, contractor, cond cap all within specs. Washed cond coil. Pressures are within specs of charging chart. All ops are normal at this time.
Arrived at customers residence and was greeted by the customer and proceeded to the thermostat and itnis functioning properly at this time. Tape and ductwork joints are tight and neat and without any visible defects and air leaks at this time. Inspected 3” pvc flue pipes and they are primed glued and pitched properly at this time. Refrigerant lines are tight and neat and Arma flex insulation is intact without any visible defects and or issues at this time. Inspected 16x25x4 media filter and it is dirty at this time. Inspected gas line and it is doped and tightened properly and is within code specifications at this time. Inspected condensate drain and it is clear at this time. Inspected condensate pump and itnis functioning properly at this time. Inspected flame sensor and ignitor and they are clean and without any visible defects at this time. Door switch is functioning properly at this time. Inspected inducer draft motor and it is functioning properly at this time. And has an amp dr
All wiring is tight and in good condition. All motor amps are in correct range per manufacturer specifications. No refrigerant leaks found at this time. The Reme halos are working properly at this time. The refrigerant pressures are in correct range per manufacturer specifications. I completed our check sheets for the systems. The systems are working properly at this time. I installed a uvcadvantage in the attic airhandler during this visit.
Arrived at customers residence and was by the customer and was led to the thermostat and it is functioning properly at this time. Inspected 14x24x1 filter and it is clean at this time. Inspected 14x14x1 filter and it is clean at this time. Refrigerant lines are tight and neat and arma flex insulation is intact and without any visible defects at this time. Tape and ductwork joints are tight and without any visible defects or air leaks at this time. Inspected disconnect and it is tight and neat to the wall at this time. Inspected condensate drain8 and it is functioning properly and is clear at this time. Inspected condensate pump and it is functioning properly at this time. Inspected Ez trap safety switch and it is functioning properly at this time. Inspected evaporator coil and it is clean and functioning properly at this time. Inspected blower motor and wheel and they are functioning properly at this time. Blower motor and wheel are clean at this time. Blower motor has an amp draw o
Arrived at customers residence and was led to the thermostat and error code 83 low pressure lockout for four hours. Put gauges on system and found that the system was flat again. Took so bubbles and covered every joint. Could not find leak at this time. After trying to trace leak from the indoor unit and the indoor coil was unable to find leak at this time. After lengthy leak search popping up system to 400 psi under the impression that leak would be heard due to the high psi. Unfortunately that was not the case today. Isolated outdoor unit pump system up with nitrogen to 300 psi. Closed both service valves to isolate outdoor unit from indoor unit to customer would be back in a couple of days to check isolated unit. Left heat pump system with the ability to use emergency heat until problem with system is resolved at this time. Spoke with Ryan Goring about the leak check and he advised me to shut an outdoor unit from indoor unit to isolate leak at this time.
Arrived at customers residence to replace evaporator coil proceeded to basement to remove leaking evaporator coil and install new evaporator at this time. Removed ez trap safety switch and CS1 safety switch to remove coil out of cabinet. Reattached both safety switches and brazed in refrigerant lines and continued on by pressure testing system 400psi and it held pressure. Found no leaks in braze joints at this time. After charging the system it is functioning properly at this time.
Arrived at customers residence and was greeted by the customer and was led to the thermostat and itnis functioning properly at this time. Inspected 20x25x1 filter and it is clean at this time. Inspected tape and duct work joints and they are tight and neat and without any visible defects at this time. Refrigerant lines are tight and neat and Arma flex insulation is intact and without any visible defects at this time.`inspected emergency shut off switch and it is functioning properly at this time. Inspected condensate drain and it is clear at this time. Inspected gas line and it is tight and neat and is within code specifications at this time. Inspected manual shut off valve and it is functioning properly at this time. Electrical connections are tight and neat to the components and wire nut connections are tight and neat and without any visible defects at this time. inspected evaporator coil and it is clean at this time. Leak checked evaporator coil found heavy rust and decay and found
Arrived at customers residence and was greeted by customer and was led to the basement and arrived at air handler and found that there is a smell of heavy ozone in the air causing the smell to fix issues suggested to customer to have fan motor run continuous to allow smell to dissapate at this time which after running system for several minutes smell has been eliminated at this time. Also customer decided to a single duct cleaning performed at this time. Customer stated that he would like to have me as his preferred technician at this time.
Arrived at the customers residence and was greeted by the customer and was led to the thermostat and it is functioning properly at this time. Inspected 20x20x1 filter and it is clean at this time. Tape and ductwork joints are tight and neat and without any visible defects or air leaks at this time. Refrigerant lines are tight and neat and Arma flex is intact and without any visible defects or issues at this time. Inspected 60 amp circuit breaker and it is functioning properly and has 244.6 volts coming in and going out at this time. Electrical connections are tight and neat to the components and wire nut connections are tight and neat and without any visible defects at this time.inspected blower motor and wheel and they are functioning properly. Blower motor has an amp draw of 2.4 amps at this time. Inspected condensate drain and it is clear at this time. Inspected evaporator coil and it is clean top and bottom at this time. Inspected condenser coil and it is clean at this time. In
Arrived at the customers residence and was greeted by the customers and was led to the thermostat and has a code 83 low pressure lockout and found that thermostat needed an update manually updated thermostat with micro chip to possibly clear code at this time increase thermostat temperature. Leak checked evaporator coil and found that coil is showing evidence of multiple leaks at this time. Leak checked outdoor unit and found no evidence of leaks at this time. Also found that refrigerant pressure is about 10 psi at this time. Leak search outdoor coil and found no evidence of leaks at this time. Office will need to contact Carrier to get pricing and other information needed at this time.
Arrived at customers residence and was greeted by the customer and was led to the thermostat and it is functioning properly at this time. Customer opted to change filters at this time and customer was given 2- 20x25x1 and 3- 16x16x1 filters upon arrival at this time. Proceeded to the crawlspace and got to airhandler. Tape and duct work joints are tight and neat and without any visible defects and or air leaks at this time. Refrigerant lines are tight and neat and Arma flex insulation is intact and without any visible defects at this time. Air handler is sitting level on a kindorf bracket attached to floor joists securely at this time. Inspected disconnect for air handler and it s tight and neat and attached to the return duct at this time.inspected ez trap safety switch and it is functioning properly at this time. Inspected CS1 safety switch attached to the secondary drain port and it is functioning properly at this time. Inspected condensate drain and it is clear at this time. Inspec
During my inspection today, the customer greeted me at the front door. He allowed me to come inside to inspect his equipment. He asked me what I would be doing today. I told him this was a post install inspection for the attic system. He informed me that he did have two systems. And then I informed him that if he wanted the second system inspected, it would be a inspection fee And it would have to be rescheduled for another day because I’m not allotted the timeframe for two systems today (per the office). He was uninterested in Having the basement system looked at at all. He stated to me that everything was running fine at this time that they haven’t had any issues. I still gave the customer the option for me to inspect that system just in case he changes his mind. he showed me around to the upstairs unit. It was in an attic. I used a 6 foot ladder to get up there. He also showed me where his filters were and his thermostat. The filters were clean at this time. Open the attic. I inspe