you're asking me to give you feedback on Christian Rice, he did not perform the work. O my God do you even know who you sent here?
On time, professional, answered questions, seemed very knowledgeable
Came out same day to give an estimate for a whole new system. No pressure to buy or up sale on more expensive systems. Helped keep house cool until new system could be installed. Patrick went above and beyond to make sure my family stayed cool without breaking the bank. Crew came out as soon as possible, worked very efficiently. Got finished with everything before the house had time to get hot again. I would highly recommend Comfort Solutions to everyone I know.
Jason handled a new HVAC system in a new home I built. We had several conversations regarding my options, his recommendations and pricing. I also contacted at least 3 other local HVAC contractors. For the quality of the equipment, Comfort Solutions was the clear choice. Comfort Solutions then exceeded my expectations with the actual installation. Great Work!
The tech they sent to look at our HVAC arrived on time, was genuinely friendly, and explained everything well.
He was quick, honest, and reasonable. I was sure I'd have to replace the entire unit, but turned out to be a little fix. Thank goodness. When this bad boy does blow, will definitely call them back to replace the unit for sure! Thank you so much
Fix dryer vent. Change 20 x 20 x1 filter.
Clean drying. Changed filter. Checked all electronic components. Checked amps on heat strip and blower motor. Both test fine. Fixed insulation on line set. Fix insulation on back of Access door On unit. Checked amps on compressor and fan. Both test fine. Heat pump performing as it should.
During today’s visit, performed inspection and maintenance on one basement, air handler and one outdoor heat pump unit. Inspected overall cleanliness of the blower and coil compartments. Inspected functionality of the auxiliary heat strips. Inspected functionality of the ultraviolet light installed. Inspected blower amp draws. Inspected temperature Heat rise and heat mode. Heat rise is within the ideal range. Inspected outdoor heat pump unit electrical components such as the Capacitors, contactor, and system amp draws. The system is functioning normally at this time.
During today’s visit, performed inspection and maintenance on one attic, air handler and one outdoor heat pump unit. Changed 16 x 20 x 5 filter. Inspected ductwork for leaks. Inspected overall cleanliness of the blower and coil compartments. Inspected indoor blower motor amp draw. Inspected temperature heat rise. Inspected functionality of auxiliary. Heat strips. Inspected outdoor condensing unit Electrical components. The system is functioning normally at this time.
On arrival, technician found that the gas line had been taken off of the hanging unit heater. Perhaps someone was attempting to hook up their own heater to gas line. Anyways, after reconnecting gas, the technician began diagnostic and found that the draft inducer assembly was not functioning. Technician was able to manually spin motor shaft and yet the heater operating however, the motor is failing and will fail again. Estimate will be provided to the customer for draft inducer assembly replacement.
I completed a two system heating maintenance. I replaced 1-16x25x1 and 1-14x25x1 filter. I cleaned flame sensors and checked igniters. I checked the amp draw on the blower motors and inducer motors. I checked capacitors and confirmed proper voltage. I checked shaft and confirmed proper sequence of operation. Both systems are currently heating at manufacturers specifications.
The system was slightly overcharged, so I let some Freon out and got the system to where it needed to be. The system is running and operating like it supposed to at this time.
Quoted to add 1 supply and 1 return for add-on room in basement once customer has framed the 8ft walls and removed garage door also rework master supply and return for existing basement. (Not charging for reworking existing ductwork because should have been done at install) Customer will call us in 3-4 weeks Pics and materials uploaded
Replacement of compressor, new liquid line filter, dryer, and 8 pounds of refrigerant. Completed replacement of compressor. I replaced the compressor and filter dryer. Pressure tested the system and pulled a deep vacuum. I added 8 pounds of 410a refrigerant and turned the system on. I adjusted the charge to get the factory required level. System is currently heating at manufacturers specifications.
Performed 3 system heat maintenance replaced 2 16x20x1 and 1 16x25x1 filters cleaned flame sensors and pressure tubes tested auxiliary and thermostat functions tested all electrical components and refrigerant charge all systems operating properly at this time
Install control Board. Heater working as it should.
Change filter. Clean drain. Check all electronic components. Checked amps on heat strip and blower motor. Both tests fine. Checked amps on outside. Compressor and fan. Both test fine. Check defrost board. Defrost board tested good. Heat pump performance as it should.
Customer just change filter. Left a filter. Clean Drain. Checked all electronic components. Checked zone dampers. Dampers test good. Checked amps on heat strip and blower motor. Both tests good. checked amp on Compressor and fan. Both test fine. Checked defrost board. Defrost board good. Heat pump performing As it should.