Pride Plumbing came out and provided a cost estimate to dig down next to the building to expose a deteriorated plastic corrugated pipe, replace the pipe with galvanized pipe and clamp collars, backfill the hole, compact the dirt, and spread grass seed and straw.
Pride Plumbing came out and provided a cost estimate to supply several Piedmont Rent-A-Jon handicap accessible port-a-jon's and handwashing stations and empty, clean, and restock with toilet paper, soap and paper towels weekly. (https://piedmontrentajon.us)
Pride Plumbing was called out for no water from a well. We provided cost estimates to either 1) replace the well's tank tee, 30/50 pump switch and gauge, charge the tank, and replace the well's submersible pump and wiring; and 2) install a new submersible pump assembly (this would include replacing the pump, piping, wiring, tank tee, and well seal).
Pride Plumbing came out and replaced a kitchen sink's P-trap, drain, and galvanized drain line through the floor to under the house in the crawlspace, and to where it ties into the main sewer drain stack, with new PVC piping and fittings.
Pride Plumbing came out and provided a cost estimate, after an unsuccessful clearing attempt, to replace a kitchen sink's P-trap, drain, and drain line through the floor to under the house in the crawlspace, and to where it ties into the main sewer drain stack, with new PVC piping and fittings due to grease buildup in the line.
Pride Plumbing came out and provided cost estimates to perform the following work: 1) replace a well tank and tee; 2) replace a leaking 40-gallon electric water heater with either a new customer supplied model or a Pride Plumbing supplied model; and 3) replace an outside sillcock.
Pride Plumbing came out and repiped and replaced the drain lines under the house in the crawlspace, going to a) the fixtures in the kitchen (sink and dishwasher), a utility sink, and one bathroom (sink, toilet, and bathtub/shower - replacing the toilet bowl's flange and wax seal gasket and the P-traps underneath all the sinks); and b) the washing machine - installing new PVC piping, fittings and supports under the house for each fixture. We also added air admittance valves to the drain lines for the kitchen and utility sinks.
Pride Plumbing came out and provided a cost estimate to repipe and replace the drain lines under the house in the crawlspace, going to a) the fixtures in the kitchen (sink and dishwasher) and one bathroom (sink, toilet, and bathtub/shower - replacing the toilet bowl's flange and wax seal, the P-traps underneath all the sinks, and the bathtub/shower's waste and overflow); and b) the washing machine - installing new PVC piping, fittings and supports under the house for each fixture.
Pride Plumbing was called out for two bathroom sinks draining slowly and a water leak underneath a kitchen sink. For the bathroom sinks, we removed both of their popup assemblies and they were full of hair and soap scum. We removed all the hair and cleaned off the soap scum, reinstalled them, tested the drains, and the issues were corrected. The kitchen sink faucet had a leak on its sprayer underneath the sink so we tightened its locking nut and stopped the leak. We also provided a cost estimate to replace the kitchen sink faucet with either a new customer supplied model or a new Pride Plumbing supplied Mainline, Olympia, or Delta model.
Pride Plumbing came out and provided a cost estimate to perform the following work: 1) cut the sheet rock behind a shower (near the showerhead) and add blocking; 2) install a new drop-ear fitting (securing it to the blocking) and run new PEX piping and fittings from the drop-ear to the shower valve.
Pride Plumbing came out to repair a galvanized bathroom sink drain behind the wall in the men’s restroom. We performed the following work: 1) we turned the water off to the wall-hung sink and then removed it from the wall along with its two P-traps; 2) we removed just enough of the concrete block wall to access the sink's galvanized drain line; 3) we cut out the bad section of drain line and replaced it with new PVC drain piping and fittings (installing a new PVC Santee and connecting back to the galvanized pipe with a Fernco coupling); 4) after the repair was made, we reinstalled the wall-hung sink and both P-traps; and 5) we installed a plastic plumbing access panel over the hole we made in the concrete wall.
Pride Plumbing came out and replaced a leaking 38-gallon electric tabletop water heater with a new 38-gallon electric tabletop model. First, we removed and disposed of the old water heater. Then we installed the new water heater, new ball water shut-off valves, new PEX and stainless steel water supply lines to the water heater connectors, a new brass drain valve, and wired up the electrical connections to the new water heater. Finally, we ensured that the unit was properly vented and set it to its appropriate operating temperature.
Pride Plumbing came out and provided cost estimates to replace a leaking 50-gallon electric tabletop water heater with either 1) a new 50-gallon electric model (this would include removing and disposing of the old water heater; installing the new water heater, new ball water shut-off valves, new PEX and stainless steel water supply lines to the water heater's water connections, a new brass drain valve, connecting the unit’s electrical connections, ensuring that the unit was properly vented, and setting it to its appropriate operating temperature); or 2) a new Navien 240A tankless model with a circulation pump (this would include a) removing and disposing of the old water heater along with its venting and gas and water supply lines; and b) installing the new tankless unit along with its service valves, PEX and stainless steel water lines to the unit's water connections, copper gas supply line, gas regulator, exhaust and intake lines, lighting and programming the water heater, and ensuri
Pride Plumbing came out and replaced a leaking 40-gallon electric water heater with a new 40-gallon electric A.O. Smith ENS-40 110 model. First, we removed and disposed of the old water heater. Then we installed the new water heater, new ball water shut-off valves, new PEX and stainless steel water supply lines to the water heater connectors, a new brass drain valve, and wired up the electrical connections to the new water heater. Finally, we ensured that the unit was properly vented and set it to its appropriate operating temperature. We also upgraded the unit's elements to 3,500 watt elements due to it being on a double pole 20 amp breaker.
Pride Plumbing came out and provided a cost estimate to perform the following work: 1) remove a section of a concrete block wall in a men's bathroom to access the galvanized drain lines; 2) cut out and replace a section of the galvanized drain line going to two bathroom sinks; and 3) replace the faucet, popup assembly and P-trap on one of the bathroom sinks.