The electrician is very knowledgeable. The company is very reliable. The workmanship is top notch. Prices Definitely on the high side.
Dispatcher reached quickly and was able to identify the problem quickly. He was polite and clear in his explanation of the issues. Regarding cost, I am always looking for a good price.
Very reliable, superior customer service. The technician was respectful, and very knowledgeable. He came prepared with all the materials and tools he needed to do the job. He worked very clean and neat! I’ve used other ac companies and no one compares to Kings air conditioning... I can’t say enough good things about this company!!! The prices are also very fair.
Completely satisfied with service.
Prices quoted were half of my company that had installed my new a/c! Happy I made the switch to King A/C
Got the job done quickly. Very polite. Didn’t try to sell me things I didn’t need or want.
Jason was great, diagnosed the problem and presented a solution.
Always a pleasure working with kings
Replace existing exhaust fan with 1.5 sones light fan combo Remove and existing vanity fixture Install (1) customer supplied vanity fixture
Diagnosis stove breaker tripping. Found: losing wires at terminal block. Fixed it temporarily by tapping with electrical tape, customer must replace terminal block as soon as possible
Supply and install new drain line from AH to outside of home.
Diagnosis dishwasher and disposal not working Found neutral wire being interrupted somewhere. Convert 2 circuit to 1 one, use other wire as neutral
1)â€”â€”Repair reversed polarity of outlet in bedroom.
1)â€”â€”Remove 3 3ft fluorescent fixtures in kitchen. 2)â€”â€”Supply and install 1 4ft LED fixture in kitchen. 3)â€”â€”Remove and replace master bathroom switches. NOTE: 1 YEAR WARRANTY
Float switch kicked on because no water in p-trap after cleaning drain Iine. Tested and worked properly
MAIN LUG CIRCUIT PANEL- 1)â€”â€”Remove 200 amp indoor main lug circuit panel. 2)â€”â€”Replace with new 200 amp indoor 42 circuit main lug panel. 3)â€”â€”Label,rough patch and clean. NOTE: The exsitng panel is to small and has no spaces left for the work needing to be done to bring kitchen up to code as we will need to add circuits and install 24 arc fault breakers in total to new circuits and exisitng to do so. DEDICATED CIRCUITS- 1)â€”â€”Run dedicated 20 amp circuit from panel to microwave location. (Approximately 70ft) 2)â€”â€”Run dedicated 20 amp circuit from panel to cooler location. (Approximately 70ft) 3)â€”â€”Run dedicated 20 amp small appliance circuit from panel to 1 set of counter top outlets in kitchen. (Approximately 70ft) Code requires 2 small appliance circuits in kitchen, right now there is only 1. 4)â€”â€”Run dedicated 40 amp cook top circuit from panel to cook top location. (Approximately 70ft) Cook top and oven are wired to same circuit that is not big enoug
1 year AC red carpet club Supply and Replace (1) regular 24v defective thermostat Supply and install (1) AC disconnect
1)â€”â€”Relocate duplex GFI outlet on inside of pit wall to exterior side of pit wall; Extend circuit using 1/2 inch PVC and install weather proof outdoor rated outlet box with weather resistant 20 amp duplex GFI outlet and bubble cover. 2)â€”â€”Run 2 20 amp dedicated circuits through existing conduit to existing junction box for quad GFI box to be installed. 3)â€”â€”Extend the 2 20 amp dedicated circuits from junction box to desired location of quad GFI box to be installed.(Will require wet saw to cut a channel in the floor for conduit installation. Additional charges will apply for wet saw rental) 4)â€”â€”Build rack and install quad GFI setup at desired location. 5)â€”â€”Remove existing standard outlet and junction box in cage and install new weather proof box with weather resistant 20 amp GFI.
Replace (1) T12 U shape ballast Replace (3) T12 fluorescent bulbs in chapel room, 16ft high (ballast is not included) Change (3) light bulbs Inspect (1) landscape light in front
Supply and install (1) surge protector for whole house
1 year AC maintenance red carpet club. 3 visits/year Performed 1st visit
Supply and install (1)float switch
1)â€”â€”Diagnose issue with circuit 17; Open panel and test breaker, check all outlets for correct voltage and ensure devices are functioning properly.