Great company, highly recommended
Friendly, on time and very knowledgeable. They did an awesome job!
Gary Petrie was our service tech which in my opinion did an excellent job, communicated well, well mannered and conscience of our surroundings. I wouldn't mind having him come back every year to service our equipment!
All my experiences with Black Hawk have been very good. Service is timely, well done, generally well explained and service people always courteous.
Punctual. Friendly, knowledgeable. Happy to have me look over his shoulder (to learn). Highly recommended.
Dan did a excellent job. He was very professional and a really nice guy. And very helpful.
I have used your electrical services twice. Both times your electricians have been great. All work has been well done and timely efficient.
Furnace clean and tune. Cycled system. Checked heat exchanger. Found some rust and corrosion in the chambers. No cracks found. Checked, removed, and cleaned burners and flame sensor. Found burners very rusted and corroded. Cleaned as best as I could. Igniter is showing be be getting worn. Igniter is showing whiting in a few areas on igniter. Tested normal at this time. Checked and adjusted gas pressures to maximize efficiency. Checked and tightened electrical connections and clamps. Cleared drain line. Preformed combustion test and found normal level in exhaust. No CO found in airstream. System is showing signs of getting worn, but operating normal at this time. Yearly maintenance is recommended to help the longevity of this unit. Job complete.
Furnace start up. Cycled system. Checked electrical connections and clamps. Found exhaust venting clamp was incorrectly installed. Removed and correctly installed. Checked venting, ok. Preformed gas leak search, no leaks found. Checked and adjusted gas pressures to maximize efficiency. Inlet and outlet pressures were checked and adjusted. Preformed combustion test. Normal levels found in exhaust. No CO found in airstream. Customer stated that the system sounded louder. And they were having duct noises. Found filter clogged. Removed and noise reduced. Replaced thermostat with correct thermostat. System operating normal at this time. Job complete.
Removed, cleaned and installed gas burners Removed, cleaned and installed flame sensor Inspected heat exchanger Tested igniter Checked condensate trap Checked blower motor Checked and tested ventor motor Checked filter Adjusted gas outlet pressure to OEM spec Recommend Replace flame sensor -Flame sensor is rusty and may not read flame. Resulting in ignition failure Inducer motor- inducer is using more power than designed for. Burners- all three burners are rusted in spots that show signed of pending failure. Ex air -169 , co in home 4ppm, showed customer cracked heat exchanger Dan Fox second opinion Tech has turned off system as it is unsafe to run Now scheduling spring AC tune ups
Installed gas furnace. (Homeowner didn’t want old t-stat)
Performed a preferred customer furnace cleaning. Cleaned the burners and the flame sensor. Checked the furnace heat exchanger. Wiped down the inside of the furnace. Checked the electrical. Cycled the furnace and performed a furnace combustion test. No issues with the furnace at this time. Changed the furnace filter.
Repaired damaged wires and rewired dishwasher.
1st year furnace clean and tune. Cycled system. Checked heat exchanger, ok. Checked, removed, and cleaned burners and flame sensor. Both ok. Checked and adjusted gas pressures to maximize efficiency. Checked and tightened electrical connections and clamps. Preformed combustion test and found normal levels in exhaust. No CO in airstream. System operating normal at this time. Job complete.
Performed the level 2 furnace cleaning. Burners and flame sensor are clean. Heat exchanger looks good. Combustion readings were normal. No CO detected in the air. Drain is clear. High limit passed the safety check. Heat rise was 49°. Unit is heating properly.
Performed the level 2 furnace cleaning. Burners and flame sensor are clean. Heat exchanger looks good. Combustion readings were normal. No CO detected in the air. Drain is clear. High limit passed the safety check. Heat rise was 34°. Unit is heating properly. We will quote and return with the filters.
Came out to investigate a shaking furnace. What I found was insulation and a dead rodent in the blower wheel cage. I had to take off the drain trap and board in order to pull out the wheel and clean everything out. Once the obstructions were cleaned out, the shaking stopped. Unit is heating properly. The noticed the inducer motor was leaking water at the bottom. We will need to replace this. Photos were uploaded.
Performed the level 2 furnace cleaning. Burners and flame sensor are clean. Heat exchanger has some rust. Excessive air levels were a little high but not concerning. No CO detected in the air. Drain is clear. High limit passed the safety check. Heat rise was 60°. Unit is heating properly.
Removed and cleaned and reinstalled flame sensor Removed and cleaned and reinstalled gas burners Checked gas outlet pressure Checked igniter Checked filter Inspected and tested inducer motor and blower motor Checked your condensate drain trap Furnace working well at this time Tune ups maintain warranty
Removed and cleaned and reinstalled flame sensor Removed and cleaned and reinstalled gas burners Checked gas outlet pressure and adjusted to 3.5 from 4.6 Checked igniter Checked filter and replaced Inspected and tested inducer motor and blower Furnace working for me today Brennan diagnosed bad gas valve, recommend replacement valve as renters are still having trouble
Furnace clean and tune. Cycled system. Checked heat exchanger, ok. Checked, removed, and cleaned burners and flame sensor. Both ok. Igniter tested ok. Checked and adjusted gas pressures to maximize efficiency. Checked and tightened electrical connections and clamps. Cleared drain lines. Preformed combustion test and found normal levels in exhaust. No CO found in airstream. Checked humidifier and found no water running to unit. Cleared saddle valve. Water running to unit now. System operating normal at this time. Job complete.