403 Headquarters Dr. Unit 5
Millersville, MD 21108
(443) 396-3797

Local Reviews
for fulton, md

Rated 4.8 out of 5 stars based on 5 customer reviews

Outstanding Timely Service

This was my 2nd time calling on Haas & Sons and once again they provided exceptional service that was timely!! They can be trusted for their expertise and I will always give them a call in the future!

  • Overall Experience
  • Quality
  • Price
  • Convenience

Great service1

Very professional and makes great recommendations!

  • Overall Experience
  • Quality
  • Price
  • Convenience

Great service!

  • Overall Experience
  • Quality
  • Price
  • Convenience

Awesome work!

Larry did a great job and was very professional.

  • Overall Experience
  • Quality
  • Price
  • Convenience

Excellent Company

The company responded quickly with an appt for us. The tech that came was very professional and personable. He knew exactly how to fix our issues and did so the same day. Very courteous and fully vaccinated!! The next time I need an electrician, I’ll call Haas

  • Overall Experience
  • Quality
  • Price
  • Convenience

Job Locations
for fulton, md

Nicholas T.

Nicholas T. Job Checkin

Replaced burnt up dryer receptacle. Provided pricing for new circuit for 240 V dryer as well as main panel replacement and safety and code updates.


Alex W.

Alex W. Job Checkin

I removed a ring security light by the garage doors. The wires went straight to the light so i installed a siding block and siliconed around the sides to prevent water getting into the hole. Then i installed a new ring security customer supplied light Customer did not have other electrical projects at this time


Genny G.

Genny G. Job Checkin

Today’s visit was for installing EV charger receptacle. I also recommend surge protection to protect home and your vehicle. Customer declined. Please see below for work performed: Install EV charger receptacle in garage with GFCI breaker Also, please attached quote if you decide to go hardwired in the future. Thank you!


Nicholas T.

Nicholas T. Job Checkin

Troubleshot new pool heater to find that there’s something wrong with the unit when it starts up. Unit is pulling 172 A are very short. Before dropping down which is causing the breaker to hum. Also, on site we installed a customer supplied floodlight on the back of the home and a pre-wired location. Replace floodlight on second story from the back of the home. Installation of customer supplied light


dennis@haasandsons.com

dennis@haasandsons.com Job Checkin

The reason for today’s visit with customer was a scheduled appointment to quote adding a receptacle to his garage for an EV charger port. After greeting with customer, we then went to the garage and assessed the area of where the charger plug would go. I saw a 3/4 inch EMT run that went to the panel ran in 6 THHN stranded copper conductor. The customer stated he had a universal plug adapter for the current tesla charger and he wanted to optimize his charging capabilities. After going over the details we then were taken to the panel which was located in the back bedroom on the second floor. The panel was a 2011 Siemens 150 amp panel with dual function breakers and one mix-matched Eaton BR breaker. I recommended to the customer we replaced the incorrect breaker along with any work he decided on scheduling for the EV charger. I went over two options for the EV charger such as the customer buying an actual wall unit EV charger and us installing it or us installing a 240v 50 amp receptacle


dennis@haasandsons.com

dennis@haasandsons.com Job Checkin

Installation of new customer supplied ceiling fan located in the bedroom on the second floor. With installation, turning current switch controlled outlet into a constant hot outlet and replacing the switch that currently controls that outlet.


Michael W.

Michael W. Job Checkin

This solution includes the installation/relocation of 2 existing receptacles to a new and higher height located within the new built in cabinet. We have relocated the existing wire for the 2 receptacles. Once the built in cabinet is in place customer to install the boxes. Arc fault protection installed in panel. Circuit was tested and works, however it shall remain off until cabinet completion.


Michael W.

Michael W. Job Checkin

We have delivered pricing regarding the deck project.


dennis@haasandsons.com

dennis@haasandsons.com Job Checkin

installation of new GFCI located in primary bathroom on second floor with properly terminating aluminum wiring with alumicon connectors. With doing so removing current single gang outlet and replacing with a 2gang outlet to further assist alumicon connectors and adding another receptacle protected by the current GFCi. Installation of GFCi located in hall bath on second floor and properly terminating.


Michael W.

Michael W. Job Checkin

This solution includes the installation of new decora switches in the kitchen area, 9 total. In addition we shall replace the 3 pendant lights with new customer supplied lighting. We shall correct the chandelier height. We have installed the new customer supplied lighting in the kitchen. In addition we have replaced existing switches in the kitchen area. 8 total.


Nicholas T.

Nicholas T. Job Checkin

Reason for today’s visit was to assess power loss to the primary bedroom as well as the garage lights. Customer stated the breaker had tripped a few times, and now would not reset. I checked the main panel and found that the breaker controlling the affected circuit was dead shorting immediately when trying to be reset. First thing I did was open up the panel and found that most of the circus have been transferred down to a sub panel below the main which had a hook up for a back up portable generator. The main panel was a 200 amp Square D panel that was original to the home. There was another 200 amp Square D panel next to this panel that had been replaced. For whatever reason the left panel was never replaced. The right panel appears to have been replaced but without a permit. There was never surge protection installed or emergency disconnects. And then began troubleshooting the circuit at the garage, because customer stated he had previous issues with the garage switch. When I opened


Michael W.

Michael W. Job Checkin

We have provided pricing for the various tasks.


Matt M.

Matt M. Job Checkin

Trouble shoot tripping gfi New wire seemed to be damage or poorly installed causing gfci to trip in garage next to panel


Michael W.

Michael W. Job Checkin

This estimate includes the installation of a customer supplied fixture in the master closet. We shall return when customer supplied material arrives. Customer has paid in full. We have installed the customer supplied wafer light in the master bedroom closet.


Alan S.

Alan S. Job Checkin

Upon inspection I found broken wires and loose splices using purple wire nuts in box for receptacle to the left of the stove that feeds the outlet for the microwave too. I will properly splice and alumicon the copper to aluminum splice and fix the broken splice and get 120 volts back to the microwave outlet in cabinet above the stove.