Dave was able to get the gaps as close as they were going to get.
Response from K&D Factory Service Inc.:
We appreciate you taking the time to leave us this positive review.
Overall Experience
Quality
Price
Convenience
Commercial Kitchen Equipment Repair: Addressing temperature fluctuations in a beer cooler, I recalibrated the thermostat. This adjustment ensures consistent cooling, preserving the quality and taste of beverages.
Commercial Kitchen Appliance Repair Service: In a busy kitchen, where worn-out knobs were affecting control, I replaced them with precision. This meticulous repair allows for precise control over the commercial range, contributing to efficient cooking.
Espresso Machine Maintenace Service: I arrived at the client’s business to perform maintenance on their espresso machine, including descaling, component replacement, and thorough cleaning. This ensured the machine operated at peak performance, consistently delivering premium espresso.
Commercial Appliance Repair Service. Arrived at the client's location on 5/31/23 - Found wash tank drain stuck and will not move. Nothing is blocked inside, will order part and return. Returned to location on 6/6/23 - Removed front panel. Found drain sent out is 1” shorter than the one currently installed. Will not work with setup. Removed and replaced dry rotted leaking coupling. Managed to break valve free with extended pipe wrench setup. Slightly hard to turn at first but got looser after messing with it. Drain functions properly with no leaks. Operational.
Commercial Kitchen Equipment Repair Service. Arrived at location and inspected the appliance to determine the source of the problem. I opened up the main kitchen and found the champion dishwasher strainer split and leaking. Will order the part. Filled kettles with water and started kettles up and convection ovens and 6 metro warmers had to replace the plug on one warmer plug was overheated. The dairy dishwasher started up and tested good.
Pilot light for conveyor pizza oven won't start. Thermocouple directly in the flame and still won't stay lit. Replace the thermocouple and pilot light is good to go now.
Arrived at location on 4/28/22 - Found the unit half full of water. Filled with water to the line and turned on. Found the thermostat is off by at least 25 degrees. Turned the calibration screw so the control would shut off when the water was boiling at 100 degrees Celsius. Need to obtain a new thermostat. Could not test further because the lack of oil in the unit. Returned to location on 5/3/22 - Found the fryer empty. Disassembled and removed the defective thermostat and installed a new one. Reassembled and filled with oil. Tested the unit. Found the calibration a hair low. Bumped the temperature up so the unit shuts off at about 320 degrees F or 160 degrees C.
Arrived at location on 10/8/21 - found unit on when here and heating. Customer using unit, will call back if unit goes down over weekend. If not will return Monday to see if can find anything wrong. Returned to location on 10/11/21 - return cycled unit on from cold start and checked cooling fans working. Unit read open on display. Played with temp probe wire, went away. Cut back wires at controller and stop reading open, unit came up to temp.
3/26/21 Examined ACC Steamer unit, found main contactor bad, will obtain and return. 3/26/21 Returned and replaced contactor pulls in 22 amps per leg heats and vaccuum, all okay.
Examined top Oven unit, found conveyor motor short, customer getting parts needed.
Removed side panels of Steamer, shut water off to unit and put 1/2 a gallon delimer into each generator, then turned water back on and flood generators - let sit without heat on and then flushed generators Note: need drain valve assembly bottom compartment - Will order on new work order.
Customer states bottom Oven conveyor chain had ripped. One link was broken and got caught and bound the whole chain. Chain section looks to be about 3.5 feet, will order 4 feet and two sets of master links to patch in. Nothing looks bent currently. Bushings in good shape, set up for early morning. Turned motor on, still moves. Lots of slack in chain from conveyor moving, only ran long enough to make sure motor turns. 1/10/2020 Replaced 1 foot of conveyor in bottom oven, made master links and tested.
Found Oven unit off, customer advised that conveyor sped up after being on for awhile - they shut unit down and later turned unit on and worked okay, checked wires at pick up and speed control board, did not find any loose, ran unit for 1/2 hour - please get price pick up and speed control board ( top oven ) Note: gave price of parts to John, he is not sure if he wants parts ordered yet. Closing out this work order.
Examined Reach In Freezer unit and found red product probe broken. Called servolift EASTERN and talked with Amber. Need P/N 3805030. They will contact Harrisburg if there is a software update available. Note: quoting additional repairs due to cost of part, closing out work order.
Found on and in use found fill valve for wash tank running and no heat in wash tank customer finished and drain unit checked float switches tested okay. cycle unit back on, unit stopped filling once notice water going down drain drain valve leaking by turn float switch assembly a little so that top float being activate need drain valve part number no-hit connector one of each 8/21 good day to do work or after labor day. 8/24/19 Removed and replaced wash tank drain valve and coupling. tested. unit filled and heated. Pre-wash 140 wash 155 rinse 180. drained unit, no leaks. good. rinse solenoid leaking by and all 3 vacuum breakers leaking will quote Note: quoting additional repairs, closing out this work order.