Arrived at location on 10/24/22 - Checked out unit and found working on arrival. Talked to customer and she said sometimes it will work ok and sometimes it won't. Found gas was not set right. Changed it to the pressure that the factory wanted it to be 3.5 and the fan shutter at 2. Cleaned the flame sensor and checked operation. Found that unit was also leaking at the door gasket. Will obtain new door gasket and ignitor and return. Unit was cycling on and off with no problem. Returned to location on 10/27/22 - Returned with parts. Removed old door gasket and ignitor and installed new. Checked operation by letting unit come up to temp. All operation ok. While waiting on unit to come up to temp maintenance came by asked them about the filters. He ran and got a filter. Change the filter and scale stick. Checked for leaks, all ok.
Arrived at location on 7/23/21 - Found unit unplugged. Accessed components. Found hv fuse bad, replaced, tested. Found 16.5a on mag circuit. ok. Checked switch. Found right switch over actuated. Unable to adjust because hinge over shoots. Paddle will break. Need new hinge and best to replace as a set. Unit ok to use. Returned to location on 8/2/21 - Replaced hinges and 20amp fuse. Unable to test unit because in back room. Customer will call after they use if issue.
HOB Under-counter Dishwasher - Removed cover panels. Removed faulty wash relay and installed new one. Replaced booster thermistors and hi limit discs. Started unit up and let fill. Filled and booster began heating followed by wash tank. Both heated to set point and cycling normally. Unit running normally at this time.
Oven unit blew 20 amp mag fuse, replaced fuse. door switches tested OK. relays working OK. mag amp draw 16.4 amps, good. previously there were terminals replaced on t.v. circuit which could be causing the issue. also could have wiring problems for the low voltage wires to the door switches. spoke with Trevor at Turbo Chef and he recommended replacing the cap for the k3 relay. will order wiring harnesses and cap and return. 8/27/20 Came in and installed new wire harness, harness and capacitor assembly. tested the unit and found fuse OK. checked mag circuit and door switch, tested OK. ran the unit and operation OK.
Found electric Oven unit off. ran. found only arcing but no ignition. found 5.5"wc to valve. tested valve found pilot valve coil open. found door adjustment chain super loose. tightened. I'd part and sourced. will return with pilot valve. 8/25/20 Found unit off. replaced pilot valve. ran. found normal operation. let cycle several times. found OK
Deep cleaned all kitchen surfaces with sanitizing solution.
Returned with parts for Toaster. installed spacer on upper drive of club and snap ring. installed new power switch. when to check operation and found that unit still doesn't power off. checked out unit and found that power switch goes to a relay found that the relay is stuck closed will obtain parts and return. 3/18/18 Returned with part. removed defective solid state relay and installed new solid state relay. tested power switch, unit working correctly. powered back on and belt started spinning, all okay.
Checked unit out. per customer unit will switch from combi to hot air and show low water. Couldn't get unit to duplicate problem. Tested on steam mode twice and combi mode twice, no problems while checking, found pressure switch cutting in and out while unit was running not always showing pressure. Will order pressure switch and solenoid and return. 4/30/18 returned with parts removed pressure switch and one way valve & installed new pressure switch and one way valve. tested unit once parts were installed. Unit working better but still showing low water every so often when in combo mode or steam. Found loose connection on motor drive board and dirty water probe. Cleaned up and ran unit on combi and steam, all okay.
Checked Fryer-Gas & found will not filter out of top spout. Took apart at quick disconnect. Cleaned & checked operation. ***Per Frymaster, no warranty issue found***
Checked and found hi limit tripped, reset. Cleared out drains due to clog. Will leave customer use unit. Call if any problems occur.
Checked & found lid won't go up. Found cable on counter weight broke. Called David at factory & gave me pt # 140225. Customer wants ordered QWP (Expedited Freight). 6-27-17 Unloaded (in warehouse) & scraped clean for repair. Then started to break free fasteners. Will order parts. 06/29/17 Returned and installed new cable assembly. Checked operation and will give an estimate on new guide belts.
Came in & removed wrapping & hooked up water, CO2 & drain.
Found unit at Ready. Ran filter to cool. Accessed components. Ran. Found .4ua on right pilot. Good flame but poor sense. Pulled pilot and cleaned. Ran. Found 1.2ua. Pilot held. Check left pilot. Found .8ua. pilot holding. Pulled and cleaned. Ran. Found 1.3ua. Pilot holding. Ran burners. Cycled normal. Let customer cook product. Found OK.