Nick and Alex were consummate professionals and extremely friendly. They provided us with the technical knowledge about the damage that occurred, what was needed to repair the damage, and identified further work that was needed to make our home code-compliant and to strengthen our protection against power surges--something that a competing electrical company did not do. We felt that they were honest and detailed and that they cared enough about our home to figure out alternatives that would cause the least amount of damage to implement the repair solution.
Alex did a very nice job. Was communicative.
Hello, Mr. Michael Wendler visited my house to install a 20A ground-fault-protected circuit in my garage, as well as a surge-protection system for my entire house. Michael did a wonderful job and was very good at explaining everything he did along the way. I had many questions (I am a retired scientist), and Michael displayed great patience going everything thoughtfully until I had all the information I needed. He is a terrific representative for Haas & Sons, and I am certain you are glad to have him. For future electrical work, I will be calling Haas & Sons and asking for Michael. Thank you, Malcolm Niedner
On time and knowledgeable service.
We will install a new service cable from the meter to a new point of attachment at the peak of the home. We will need to install a new ground and system to port to bring it up to today’s requirements. We will pull an electrical permit and coordinate county inspections as well as the Power company final time. We are unable to open the panel cover at this time without opening up the wall. If when work is being performed and we find damage or anything that needs to be addressed there will be an additional charge for needed work to be performed.
Provided pricing to replace the overhead service cable from the meter to a new point of attachment at the peak of the home. We will pull electrical permit and coordinate county inspections. We will bring grounding system up to today’s safety and code requirements.
I removed and replaced a dimmer switch that was only rated for incandescent light fixtures. I replaced it with a dimmer switch that can be used for LED or incandescent lights I installed a customer supplied led surface mounted light fixture #review
Checked to see why receptacles in the kitchen were not working and why the light in the hallway wasn’t working.
Original call was to check the intermittent power in the kitchen lighting. I noticed improper connections to the switches and receptacles, stab in method was used. When I inspected the panel I found scorched and loose breakers. In addition upon inspection of the meter and main breaker located in the meter stack I found the breaker was damaged and weathered. This breaker at the meter was loosing an entire phase. I recommended that this breaker and the panel as well as the kitchen lighting circuit be restored to new condition. We replaced the breaker at the meter stack (Siemens 100A), the existing panel and replaced all devices on the the lighting circuit for the kitchen ensuring proper terminations.
i Ran a new switch leg for new led wafer recess lights i installed and a new customer supplied ceiling fan i installed. I installed a side mounted ceiling fan box to support the fan. I ran a 14-3 wire from switch to fan then jumped out on a separate switch leg to the recess lights Customer has a 1 year warranty.
Removed and replaced switches in basement Removed damaged receptacle and replaced it with tamper resistant receptacle Removed burnt out light fixture replaced it with company supplied LED 2x2 flat panel light fixture 1 year warranty
Swapped light in living area with ceiling fan in bedroom.
This estimate includes the installation of a new receptacle and plate. This estimate includes the installation of a 30A receptacle for the dryer We have installed a receptacle for the Dryer and Range.
This estimate includes the installation of a 3prong surface mount range receptacle. In addition We shallthe install a 3prong stove/range whip supplied By customer. We have installed a new 3prong range plug.
I ran 2 dedicated circuits through the basement from the main electrical panel to two different destinations One in the corner of the home in the basement and one in the laundry room in the basement Both are 20 amp circuits for sub pumps I installed two 20 amp cutler hammer Black and Tan arc fault breakers I installed a pvc sleeve from the ceiling joists to the 1900 box for better protection for the romex wire. Then I installed Gfcis with RS cover plates Customer has a 1 year warranty
This estimate includes the installation of a new tandem BR 20A breaker to power washer and dryer. We have installed a new tandem breaker to operate the kitchen and washer/dryer. We recommend that the panel be replaced.
This estimate includes the installation of 2new Eaton BR type breakers. One being a tandem 15A and the second a single pole 20A. We have replaced the 2 non working breakers with new devices. Circuits are working upon departure. We recommend, due to age, the panel be replaced.
This estimate includes the installation of a new EV 120V 20A. In addition we shall alleviate the double tapped neutrals and include whole home surge protection. We have begun installation of the dedicated circuit. We shall return Wednesday the 22nd of September to complete work. We have returned and completed scheduled work. We have installed new whole home surge protector, wired in EV Charger circuit and have alleviated the double tapped neutral wiring in main panel.
This estimate includes the installation of a new customer supplied doorbell camera. We shall furnish and install wiring from transformer to front door. We have installed a new customer supplied door bell camera. In addition we have installed new wiring, transformer and chime for doorbell operations. We have also replaced devices on the first floor and have provided Arc-Fault protection for the living room and itâ€™s lighting circuit. Lastly we have provided estimates regarding exterior light and master bedroom fan.